Outdoors
Bronze Outdoors: What Weather Does to the Finish
Bronze left outside changes colour every season. What importers should sell, wax and warn customers about, written from a Vietnamese foundry floor.

Bronze kept outdoors does not hold the colour it shipped in. Inside one wet season the high points brighten, the hollows darken, and rain running off the piece streaks one side. That is weathering, not a casting fault. Your work as the importer is to pick the right finish for outdoor use, say plainly what is coming, and put a wax routine in the carton.
Two roads a piece can take outside
A sealed piece leaves us with a patina, lacquer over it and wax over that. The wax wears first, which is the point: wax is cheap to replace, lacquer is not. Re-waxed twice a year the lacquer stays sound; skipped for a few years it fails in patches, and the piece needs stripping and recoating.
An open piece is waxed only, or bare, and is meant to move. Brown drifts to brown-green, then to an uneven green-grey — darker where water sits, lighter where hands and weather rub it. Once that layer forms it protects the metal beneath. Tell that customer at the counter that year three will not look like week one. Both roads are decided on the order, and the eight finishes we apply behave differently outside.
What actually attacks the surface
- Standing water in hollows, bowl rims and open crane wings. Drainage is a drawing decision, not a field repair.
- Irrigation spray, especially hard or chlorinated water, which leaves a white mineral crust that looks like a defect and is not.
- Salt — coastal air, and road de-icing salt thrown up in winter. This is the fastest way to pit a surface.
- Bird droppings, acidic enough to etch lacquer within days in summer.
- Pressure washers, steel wool and abrasive pads, which strip more patina in ten minutes than weather takes off in ten years.
- Soil and fertiliser banked against a base.

A routine you can print and put in the box
| Task | How often | Time per piece | What it prevents |
|---|---|---|---|
| Gentle hose rinse, top down, no pressure | Monthly in the wet or dusty season | 5 min | Mineral crust, bonded dust film |
| Wash with neutral, non-ionic detergent and a soft plastic brush | Twice a year | 20–30 min | Acid etching from droppings and soil |
| Dry fully, then paste wax on a warm — not hot — surface and buff | Twice a year, spring and autumn | 30–45 min | Coating wear, pitting, dull patches |
| Check base fixings and weep holes | Twice a year | 5 min | Trapped water, movement in wind |
| Look over the leanest sections for knocks | Once a year | 10 min | Dents becoming cracks |
Two thin wax coats beat one thick one, and water trapped under wax fogs the surface. The indoor version of this routine is in bronze care and storage for distributors.
What we cast differently when a piece is going outside
- Metal where the load is. Our standard body wall is 5 mm, going to 8 mm at load-bearing points — feet, handles, joints, the neck of a crane. Outdoors that decides whether a piece survives being lifted by one wing.
- Fixing built in, not drilled later. Say before casting whether the piece is bolted, pinned or free-standing, and we cast the base to suit.
- Weep holes placed on the drawing for anything that can hold water.
- Tolerance stated up front. Hand casting varies: 1–3 cm off the drawing is normal and we say so; more than 5 cm is a fault and we recast. If a mason pours a plinth before the piece lands, build that window into his measurements.
- Time. Casting runs 21–30 days after the drawing or sample is approved. Count an opening date backwards from that, plus sea time.
Weight is the first number your landscaper asks for
Solid cast bronze is heavier than photographs suggest. For a sense of the density, a size-65 five-piece altar set — an indoor product cast to the same wall thickness — runs about 36 kg, its crane standing 5–7 cm taller than the burner. A two-person lift long before it looks like one.
We state weight per piece on the quotation rather than publishing a table for pieces we have not cast yet. Ask early: it sets your crate count, your inland freight, and how the shipment is packed — see packing bronze for sea freight. Larger single pieces sit in statues and figures.
Bronze against cast iron and aluminium
Most garden and landscape wholesalers we talk to already stock cast iron or cast aluminium figures, and almost none stock bronze. Before you add a bronze line it is worth being clear about what changes on your shelf, because the three metals fail in completely different ways. We cast bronze only, so we are not a neutral judge of the other two — what follows is what each metal does to your returns, your complaints and your display piece.
| Cast bronze | Cast iron | Cast aluminium | |
|---|---|---|---|
| What ageing looks like | The metal itself darkens and greens. Uneven, and it is the material, not a coating giving up | Paint or coating breaks, then rust starts at that point | Coating chalks or flakes; the metal underneath does not rust |
| What a chip or scratch shows | The same metal underneath — it reads as wear, and can be re-patinated and waxed | Bare grey iron that goes orange, and can stain paving or stone below it | Bright white-grey metal against the paint, which shows clearly |
| Upkeep the customer is asked to do | Wax twice a year; lacquer only needs attention after years of skipped waxing | Touch-up paint, and repainting once rust is under the film | Touch-up paint or powder recoating |
| Weight for the same piece | Heaviest of the three; stands in wind without anchoring | Heavy | Lightest; cheapest to freight, but light pieces move and customers notice the feel |
| Where it sits in a range | Top tier. Bronze metal costs more than iron or aluminium, so it is the piece that anchors a display, not the volume line | Mid | Volume |
| Repair years later | The foundry can re-finish it, and can re-cast a matching piece from the same pattern | Welding and repainting, usually locally | Welding aluminium is specialist work; often replaced instead |
The practical reading: aluminium and iron win on landed cost, bronze wins on what happens in year five. A rust streak down a client’s limestone step becomes your problem; a bronze piece going greener does not, provided you said at the counter that it would. If you want one bronze piece as the anchor of an otherwise aluminium display, that is a sensible first order, and we will quote a single piece — weight per piece is stated on the quotation, and crating for a heavy piece is set out in packing bronze for sea freight.
What we cannot tell you is a price comparison: we do not publish prices and we do not quote metals we never pour. Send the same line list you would send an iron supplier and compare the two quotations yourself.
What we will not tell you
- No lifespan in years. Nobody can give an honest figure for a microclimate they have never stood in.
- No audit certificate. We hold no ISO, BSCI or SEDEX certification and say so wherever it comes up. Instead: a video call from the floor, a visit to the foundry, or the pieces in front of you in our showrooms in Nam Dinh, Hanoi and Hai Phong.
- No claim that a patina is a weatherproof coating. Patina is a surface, wax is the sacrificial layer, maintenance is the difference.
Frequently asked questions
Will an outdoor piece turn green?
Over years, if it is not sealed and re-waxed, yes — unevenly, and faster in salt air. A lacquered and waxed piece holds its shipped colour far longer, provided the wax is replaced twice a year.
Can you supply pieces already finished to look weathered?
Yes. A green-toned patina is applied at the bench and carries a finish code on the order, so a reorder can be matched to it. It is a finish, not accelerated weathering, and it still needs wax.
Do you lacquer everything before shipping?
No — it is your call on the order. Garden retail usually wants lacquer; altar customers often want wax only, because lacquer changes how the surface takes smoke and handling.
A piece arrives with a scratched finish. Is that a claim?
A damaged finish is a claim; a colour that reads differently under your shop lights usually is not. Photograph it in daylight beside the carton and its label before unpacking further.
Can you cast a heavier base or a fixing plate?
Yes, if it is on the drawing before the mould is made. Adding a plate afterwards means welding and refinishing, which shows.
Planning an outdoor line for next season? Send a line list — item, size, finish, quantity, destination port — through the request a quote form or on WhatsApp at +84 926 199 999. A quotation comes back in two working days, weight per piece included.